NDT is divided into various methods of nondestructive testing, each based on a particular scientific principle. These methods may be further subdivided into various techniques. The various methods and techniques, due to their particular natures, may lend themselves especially well to certain applications and be of little or no value at all in other applications. Therefore choosing the right method and technique is an important part of the performance of NDT.
An example of Ultrasonic Testing (UT) on blade roots of a V2500 IAE aircraft engine.
Step 1: The UT probe is placed on the root of the blades to be inspected with the help of a special borescope tool (video probe).Step 2: Instrument settings are input.
Step 3: The probe is scanned over the blade root. In this case, an indication (peak in the data) through the red line (or gate) indicates a good blade; an indication to the left of that range indicates a crack.
- Liquid penetrant testing (PT or LPI)
Liquid penetrant inspection is a widely applied and low-cost inspection method used to locate surface-breaking defects in all non-porous materials (metals, plastics, or ceramics). Penetrant may be applied to all non-ferrous materials, but for inspection of ferrous components magnetic particle inspection is preferred for its subsurface detection capability. LPI is used to detect casting and forging defects, cracks, and leaks in new products, and fatigue cracks on in-service components.
Principles
LPI is based upon capillary action, where low surface tension fluid penetrates into clean and dry surface-breaking discontinuities. Penetrant may be applied to the test component by dipping, spraying, or brushing. After adequate penetration time has been allowed, the excess penetrant is removed, and a developer is applied. The developer helps to draw penetrant out of the flaw where a visible indication becomes visible to the inspector. Inspection is performed under ultraviolet or white light, depending upon the type of dye used - fluorescent or nonfluorescent (visible).
Materials
Penetrants are classified into sensitivity levels. Visible penetrants are typically red in color, and represent the lowest sensitivity. Fluorescent penetrants contain two or more dyes that fluoresce when excited by ultraviolet (UV-A) radiation (also known as black light). Since FPI is performed in a darkened environment, and the excited dyes emit brilliant yellow-green light that contrasts strongly against the dark background, this material is more sensitive to small defects.
When selecting a sensitivity level one must consider many factors, including the environment under which the test will be performed, the surface finish of the specimen, and the size of defects sought. One must also assure that the test chemicals are compatible with the sample so that the examination will not cause permanent staining, or degradation. This technique can be quite portable, because in its simplest form the inspection requires only 3 aerosol spray cans, some paper towels, and adequate visible light. Stationary systems with dedicated application, wash, and development stations, are more costly and complicated, but result in better sensitivity and higher sample through-put.
Inspection Steps
Below are the main steps of Liquid Penetrant Inspection:
1. Pre-cleaning:
The test surface is cleaned to remove any dirt, paint, oil, grease or any loose scale that could either keep penetrant out of a defect, or cause irrelevant or false indications. Cleaning methods may include solvents, alkaline cleaning steps, vapor degreasing, or media blasting. The end goal of this step is a clean surface where any defects present are open to the surface, dry, and free of contamination.
2. Application of Penetrant:
The penetrant is then applied to the surface of the item being tested. The penetrant is allowed time to soak into any flaws (generally 10 to 30 minutes). The soak time mainly depends upon the material being testing and the size of flaws sought. As expected, smaller flaws require a longer penetration time. Due to their incompatible nature one must be careful not to apply visible red dye penetrant to a sample that may later be inspected with fluorescent penetrant.
3. Excess Penetrant Removal:
The excess penetrant is then removed from the surface. Removal method is controlled by the type of penetrant used. Water-washable, solvent-removable, lipophilic post-emulsifiable, or hydrophilic post-emulsifiable are the common choices. Emulsifiers represent the highest sensitivity level, and chemically interact with the oily penetrant to make it removable with a water spray. When using solvent remover and lint-free cloth it is important to not spray the solvent on the test surface directly, because this can the remove the penetrant from the flaws. This process must be performed under controlled conditions so that all penetrant on the surface is removed (background noise), but penetrant trapped in real defects remains in place.
4. Application of Developer:
After excess penetrant has been removed a white developer is applied to the sample. Several developer types are available, including: non-aqueous wet developer, dry powder, water suspendible, and water soluble. Choice of developer is governed by penetrant compatibility (one can't use water-soluble or suspedible developer with water-washable penetrant), and by inspection conditions. When using non-aqueous wet developer (NAWD) or dry powder the sample must be dried prior to application, while soluble and suspendible developers are applied with the part still wet from the previous step. NAWD is commercially available in aerosol spray cans, and may employ acetone, isopropyl alcohol, or a propellant that is a combination of the two. Developer should form a thin, even coating on the surface.
The developer draws penetrant from defects out onto the surface to form a visible indication, a process similar to the action of blotting paper. Any colored stains indicate the positions and types of defects on the surface under inspection.
5. Inspection:
The inspector will use visible light with adequate intensity (100 foot-candles is typical) for visible dye penetrant. Ultraviolet (UV-A) radiation of adequate intensity (1,000 micro-watts per centimeter squared is common), along with low ambient light levels (less than 2 foot-candles) for fluorescent penetrant examinations. Inspection of the test surface should take place after a 10 minute development time. This time delay allows the blotting action to occur. The inspector may observe the sample for indication formation when using visible dye, but this should not be done when using fluorescent penetrant. Also of concern, if one waits too long after development the indications may "bleed out" such that interpretation is hindered.
6. Post Cleaning:
The test surface is often cleaned after inspection and recording of defects (if found), especially if post-inspection coating processes are scheduled.
Features
- The flaws are more visible, because:
- The defect indication has a high visual contrast (e.g. red dye against a white developer background, or a bright fluorescent indication against a dark background).
- The developer draws the penetrant out of the flaw over a wider area than the real flaw, so it looks wider.
- Limited training is required for the operator — although experience is quite valuable.
- Low testing costs.
- Proper cleaning is necessary to assure that surface contaminants have been removed and any defects present are clean and dry. Some cleaning methods have been shown to be detrimental to test sensitivity, so acid etching to remove metal smearing and re-open the defect may be necessary.
- Penetrant dyes stain cloth, skin and other porous surfaces brought into contact. One should verify compatibility on the test material, especially when considering the testing of plastic components.
- Further information on inspection steps may be found in industry standards (e.g. the American Welding Society, American Society for Testing and Materials, the British Standards Institute, and the Society for Automotive Engineers).
- Radiographic testing (RT)
Radiographic Testing (RT), or industrial radiography, is a nondestructive testing (NDT) method of inspecting materials for hidden flaws by using the ability of short wavelength electromagnetic radiation (high energy photons) to penetrate various materials.
Either an X-ray machine or a radioactive source (Ir-192, Co-60, or in rare cases Cs-137) can be used as a source of photons. Neutron radiographic testing (NR) is a variant of radiographic testing which uses neutrons instead of photons to penetrate materials. This can see very different things from X-rays, because neutrons can pass with ease through lead and steel but are stopped by plastics, water and oils.
Since the amount of radiation emerging from the opposite side of the material can be detected and measured, variations in this amount (or intensity) of radiation are used to determine thickness or composition of material. Penetrating radiations are those restricted to that part of the electromagnetic spectrum of wavelength less than about 10 nanometres.
Inspection of welds
The beam of radiation must be directed to the middle of the section under examination and must be normal to the material surface at that point, except in special techniques where known defects are best revealed by a different alignment of the beam. The length of weld under examination for each exposure shall be such that the thickness of the material at the diagnostic extremities, measured in the direction of the incident beam, does not exceed the actual thickness at that point by more than 6%. The specimen to be inspected is placed between the source of radiation and the detecting device, usually the film in a light tight holder or cassette, and the radiation is allowed to penetrate the part for the required length of time to be adequately recorded.
The result is a two-dimensional projection of the part onto the film, producing a latent image of varying densities according to the amount of radiation reaching each area. It is known as a radiograph, as distinct from a photograph produced by light. Because film is cumulative in its response (the exposure increasing as it absorbs more radiation), relatively weak radiation can be detected by prolonging the exposure until the film can record an image that will be visible after development. The radiograph is examined as a negative, without printing as a positive as in photography. This is because, in printing, some of the detail is always lost and no useful purpose is served.
Before commencing a radiographic examination, it is always advisable to examine the component with one's own eyes, to eliminate any possible external defects. If the surface of a weld is too irregular, it may be desirable to grind it to obtain a smooth finish, but this is likely to be limited to those cases in which the surface irregularities (which will be visible on the radiograph) may make detecting internal defects difficult.
After this visual examination, the operator will have a clear idea of the possibilities of access to the two faces of the weld, which is important both for the setting up of the equipment and for the choice of the most appropriate technique.
Defects such as delaminations and planar cracks are difficult to detect using radiography, which is why penetrants are often used to enhance the contrast in the detection of such defects. Penetrants used include silver nitrate, zinc iodide, chloroform and diiodomethane. Choice of the penetrant is determined by the ease with which it can penetrate the cracks and also with which it can be removed. Diiodomethane has the advantages of high opacity, ease of penetration, and ease of removal because it evaporates relatively quickly. However, it can cause skin burns.
- Ultrasonic testing (UT)
In ultrasonic testing, very short ultrasonic pulse-waves with center frequencies ranging from 0.1-15 MHz and occasionally up to 50 MHz are launched into materials to detect internal flaws or to characterize materials. It is also commonly used to determine the thickness of the test object - monitoring pipework corrosion being a good example.
Ultrasonic Inspection is often performed on steel and other metals and alloys, though it can be used on concrete and other materials such as composites. It is a form of non-destructive testing used in many industries including aerospace, automotive and other transportation sectors.
How it works
In ultrasonic testing, a transducer connected to a diagnostic machine is passed over the object being inspected. In reflection (or pulse-echo) mode, the transducer sends pulsed waves through a couplant (such as water or oil) on the surface of the object, and receives the "sound" reflected back to the device. Reflected ultrasound comes from an interface - such as the back wall of the object or from an imperfection. The screen on the calibrated diagnostic machine displays these results in the form of a signal with an amplitude representing the intensity of the reflection and the distance taken for the reflection to return to the transducer. In attenuation (or through-transmission) mode, a transmitter sends ultrasound through one surface, and a separate receiver detects the amount that has reached it on another surface after travelling through the medium. Imperfections or other conditions in the space between the transmitter and receiver reduce the amount of sound transmitted thus indicating their presence.
Advantages
- Superior penetrating power, which allows the detection of flaws deep in the part.
- High sensitivity, permitting the detection of extremely small flaws.
- Only one surface need to be accessible.
- Greater accuracy than other nondestructive methods in determining the depth of internal flaws and the thickness of parts with parallel surfaces.
- Some capability of estimating the size, orientation, shape and nature of defects.
- Nonhazardous to operations or to nearby personnel and has no effect on equipment and materials in the vicinity.
- Capable of portable or highly automated operation.
Disadvantages
- Manual operation requires careful attention by experienced technicians
- Extensive technical knowledge is required for the development of inspection procedures.
- Parts that are rough, irregular in shape, very small or thin, or not homogeneous are difficult to inspect.
- Surface must be prepared by cleaning and removing loose scale, paint, etc. (UT can often be used successfully through paint that is properly bonded to a surface.)
- Couplants are needed to provide effective transfer of ultrasonic wave energy between transducers and parts being inspected unless a non-contact technique is used. Non-contact techniques include Laser and Electro Magnetic Acoustic Transducers (EMAT).
- Inspected items must be water resistant, when using water based couplants that do not contain rust inhibitors.
- Visual and optical testing (VT)
- Electromagnetic testing (ET)
The term "Electromagnetic Testing" is often intended to mean simply Eddy-Current Testing (ECT). However with an expanding number of electromagnetic and magnetic test methods, "Electromagnetic Testing" is more often used to mean the whole class of electromagnetic test methods, of which Eddy-Current Testing is just one.
- Acoustic emission testing (AE)
Acoustic emission testing is used as a type of nondestructive testing technology. It is in the ultrasonic regime, typically within the range between 100 kHz and 1 MHz (although this range is not absolute). Acoustic emissions can be monitored and detected in frequency ranges under 1 kHz and have been reported at frequencies up to 100 MHz. Rapid stress-releasing events generate a spectrum of stress waves starting at 0 Hz and typically falling off at several MHz, but one strength of the technique is that background noise, particularly airborne, falls off more quickly, so the signal-to-noise ratio reaches an optimum value around the conventional frequency range.
A commonly accepted definition for AE is a transient elastic waves within a material due to localized stress release. Hence, a source which generates one AE event is the phenomenon which releases elastic energy into the material, which then propagates as an elastic wave. AE events can also come quite rapidly when materials begin to fail, in which case AE activity rates are studied as opposed to individual events. AE events that are commonly studied include the extension of a fatigue crack, or fiber breakage in a composite material among material failure processes. AE is related to an irreversible release of energy, and can be generated from sources not involving material failure including friction, cavitation and impact.
Transducers are attached to the material to detect these waves. Most of these sensors are in the frequency range of 20 kHz to 650 kHz. Some geophysical studies with AE use much lower frequency sensors, while sensors in the MHz range are also available commercially.
AE tools do not actively produce waves (or "insonify") as in conventional ultrasonics. Rather, they passively detect emissions from acoustic sources.
AEs from within a material are monitored to locate and/or define their source event. AE is even more commonly used to correlate when activity occurred with the level of stimuli or length of time before something occurred, such as determining the onset of cracking, documenting the failure of a part during unattended monitoring or the level of reoccurrence of AE during multiple load cycles. The last method listed is the basis for many safety inspection methods utilizing AE. Parts inspected with AE can remain in service.
- Infrared and thermal testing (IR)
- Laser testing
- Leak testing (LT)
Posts
0 comments
Post a Comment